RouterOS Packet Capture & TZSP Streaming

RouterOS has a built-in packet sniffer (/tool/sniffer) and firewall mangle actions that can mirror traffic — either saving to a file on the router or streaming live to a remote host via TZSP (TaZmen Sniffer Protocol). This is the primary way to capture packets on RouterOS since standard tools like tcpdump do not exist (see routeros-fundamentals skill).

Why This Matters for Agents

When debugging any network protocol issue on RouterOS, agents should know they can:

1. Stream live packets from the router to the host machine via TZSP — no hardware needed if using a CHR VM
2. Save pcap/pcapng files on the router's flash and download them for analysis
3. Use firewall mangle rules for surgical, per-flow packet mirroring without touching the sniffer config

Combined with a QEMU CHR instance (see routeros-qemu-chr skill), this gives agents a complete packet-level debugging workflow with zero physical hardware.

Method 1: /tool/sniffer (Full Capture Tool)

The built-in sniffer captures packets on specified interfaces with extensive filtering. It supports three independent output modes that can be combined:

Live TZSP Streaming

# Configure sniffer to stream via TZSP to a remote host
/tool/sniffer
set streaming-enabled=yes streaming-server=<RECEIVER-IP>:37008

# Optional: filter to a specific interface or protocol
set filter-interface=ether1
set filter-ip-protocol=icmp

# Start capture (runs until stopped or router reboots)
/tool/sniffer/start

# Stop when done
/tool/sniffer/stop

The receiver host runs Wireshark, tshark, or another TZSP-capable tool (see TZSP receivers reference).

File-Based Capture

# Capture to file on router flash
/tool/sniffer
set file-name=capture.pcap filter-interface=ether1

/tool/sniffer/start
# ... let it capture ...
/tool/sniffer/stop

# Or save the memory buffer to a file manually
/tool/sniffer/save file-name=/flash/debug.pcap

# Download via SCP or fetch
# From the host:
# scp admin@<ROUTER-IP>:/flash/debug.pcap .

File + streaming can run simultaneously:

/tool/sniffer
set file-name=capture.pcap streaming-enabled=yes streaming-server=<RECEIVER-IP>:37008
/tool/sniffer/start

Quick Mode (Interactive CLI)

For quick one-off inspection directly on the router console:

# Quick-capture ICMP traffic on ether1
/tool/sniffer/quick ip-protocol=icmp interface=ether1

This shows a live scrolling table on the console with source/dest MAC, IP, protocol, and size.

Sniffer Filter Properties

Key filter options for /tool/sniffer/set:

Important: filter-stream=yes (default) excludes the sniffer's own TZSP stream packets from the capture — leave this on to avoid feedback loops.

Method 2: Firewall Mangle (Targeted Mirroring)

Firewall mangle rules offer granular per-flow mirroring using the full firewall matcher. Two sniff-related actions exist:

action=sniff-tzsp (Stream to Remote TZSP Receiver)

Mirrors matching packets as TZSP to a remote host. Uses the firewall's full matching engine (src/dst address, protocol, port, connection state, interface, etc.):

# Mirror all forwarded ICMP to a TZSP receiver
/ip/firewall/mangle
add action=sniff-tzsp chain=forward protocol=icmp \
    sniff-target=<RECEIVER-IP> sniff-target-port=37008 \
    comment="TZSP mirror ICMP to Wireshark"

# Mirror traffic from a specific host
/ip/firewall/mangle
add action=sniff-tzsp chain=forward src-address=192.168.88.100 \
    sniff-target=<RECEIVER-IP> sniff-target-port=37008

# Mirror DNS queries
/ip/firewall/mangle
add action=sniff-tzsp chain=forward protocol=udp dst-port=53 \
    sniff-target=<RECEIVER-IP> sniff-target-port=37008

Properties for sniff-tzsp:

• sniff-target (IP) — destination IP for the TZSP UDP packets
• sniff-target-port (port, default 37008) — destination UDP port
• sniff-id — optional identifier tag

Key behavior: sniff-tzsp acts like passthrough — after matching, the packet continues to the next mangle rule. The original packet is NOT modified or dropped; only a copy is sent as TZSP.

Mangle vs /tool/sniffer: When to Use Which

TZSP Protocol Overview

TZSP is a simple UDP encapsulation — the router wraps the original Ethernet frame in a TZSP header and sends it as a UDP datagram:

UDP (port 37008) → TZSP header (4 bytes) → tags (variable) → TAG_END → original Ethernet frame

• Default port: 37008 (0x9090) — not IANA-registered but the RouterOS/Wireshark standard
• Encapsulation: Typically Ethernet (type 1); 802.11 for wireless captures
• Tags: Optional metadata (WLAN signal strength, channel, etc.); Ethernet captures usually have no tags
• Keepalives: Type 4 (Null) packets sent periodically — no inner frame, filter these when processing

CHR Testing Pattern

A QEMU CHR instance provides a complete packet capture lab with zero hardware. The free CHR license has a 1 Mbps speed limit but this is sufficient for protocol debugging and sniffer testing.

# 1. Boot a CHR instance with port forwarding for REST API and SSH
qemu-system-x86_64 -M q35 -m 256 \
  -drive file=chr.img,format=raw,if=virtio \
  -netdev user,id=net0,hostfwd=tcp::9180-:80,hostfwd=tcp::9122-:22 \
  -device virtio-net-pci,netdev=net0 \
  -display none -serial stdio

# 2. Configure sniffer via REST API once booted
curl -u admin: -X POST http://<router-ip>/rest/tool/sniffer/set \
  -H 'Content-Type: application/json' \
  -d '{"streaming-enabled":"yes","streaming-server":"10.0.2.2:37008"}'

# 3. Start capture
curl -u admin: -X POST http://<router-ip>/rest/tool/sniffer/start

# 4. Listen for TZSP on the host
tshark -i any -f "udp port 37008" -O tzsp

# 5. Generate test traffic (e.g., ping from the CHR)
curl -u admin: -X POST http://<router-ip>/rest/ping \
  -H 'Content-Type: application/json' \
  -d '{"address":"8.8.8.8","count":"3"}'

QEMU user-mode networking note: The CHR's default gateway (10.0.2.2) is the host. Use this IP as streaming-server when using QEMU -netdev user. The host must listen on all interfaces (or 10.0.2.2 specifically) to receive the TZSP packets.

For full QEMU setup details